What is the average size of an industrial piercing?

Standard piercing sizes

Piercing Standard Gauge Standard Length
Industrial Barbell 14G (16G is also commonly used) 1 1/2″ (varies)
Labret Lip Rings 14G or 16G 1/4″ , 5/16″, and 3/8″
Monroe Piercing 16G 1/4″ , 5/16″ and 3/8″
Nipple Piercing 14G 3/8″ , 1/2″, 9/16″

>> Click to read more <<

Likewise, what is the best jewelry for industrial piercing?

Circular barbells, labret studs, and captive rings all work well in industrial piercing holes if you do not want to wear a standard barbell. There’s also a really neat piece of jewelry called a spiral that can be twisted in and out of both holes to wrap around the top of the ear.

Keeping this in consideration, are there different sizes of industrial piercings? Sizes. The standard size of a piercing diameter is usually 14 gauge, but some even go with a 16 gauge at first and then upgrade to a 14 gauge after the piercing has healed. It is actually easier to heal if the piercings are first pierced with captive bead rings in the hole, until the piercings have healed.

Correspondingly, how much is a industrial piercing earring?

An industrial piercing should cost you between $40 and $70, but if you book with a piercer in a quieter location, you can look to narrow the price down further to between $40-$50.

What does an industrial piercing say about you?

Industrial Piercing

You tend to draw people in with your charming personality, but you only have a few very close friends. You‘re less likely to get hurt that way, because you may look all rough and tumble, but you‘re a big softy on the inside.

Do Industrial Bar holes close?

The industrial piercing goes through cartilage in your ear and depending on how long it has been pierced it will close eventually and faster than many other piercings because of the location.

Do industrial piercings cost more?

Although the industrial piercing consists of two piercings, you’ll usually only be charged for one. It typically costs somewhere around $30 – $70. As always, choose a quality piercer over expense. Never go to a piercer who uses a piercing gun.

Do industrial piercings get infected easily?

Industrial piercings are more prone to infection because there are 2 wounds, and the tension placed on the skin from the jewelry also increases inflammation and vulnerability to the skin. An infection occurs when harmful bacteria build up in one or both of the holes where your ear is pierced.

Is industrial piercing worth it?

Industrial piercings look absolutely awesome, but you have to take very good care of them. Cartilage piercings generally take longer to heal, and an industrial is two piercings rather than one.

What length is my Industrial bar?

38 mm

Are all industrial bars the same size?

The barbell piercing worn in the ear cartilage goes by a few different names : The barbell is called an industrial barbell, construction bar, or industrial project bar. Sizing of these bars varies depending on the person, because everybody’s ears are a different size.

How do I know what gauge my industrial piercing is?

Piercing Gauge Sizes

  1. BCR: Measure the width of the bar.
  2. Labret: Measure the width of the bar.
  3. Barbell: Measure the width of the bar.
  4. Septum Ring: Measure the width of the ring at its thickest section.
  5. Tunnels & Plugs: Measure the circumference of the inside of your ear.

Are industrial piercings 14 gauge?

Internationally,

Piercing Standard Gauge
Tongue Piercing 14G
Cartilage Piercing 16G , 18G
Eyebrow Piercing 16G (14G is also commonly used)
Industrial Barbell 14G (16G is also commonly used)

How bad does a industrial piercing hurt?

Industrial piercings are moderately painful. While they tend to hurt more than standard lobe piercings, they’re still much less painful than piercings on more sensitive areas. … The initial piercing pain is a sharp pain, like a hard pinch, and you may also experience some pain as the jewelry is pushed in place.

Is industrial piercing for guys?

Industrial piercings are a popular cartilage piercing for guys and girls alike.

Leave a Reply