Standard piercing sizes
| Piercing | Standard Gauge | Standard Length |
|---|---|---|
| Tongue Piercing | 14G | 5/8″ |
| Cartilage Piercing | 16G , 18G | 3/16″ , 1/4″ and 5/16″ |
| Eyebrow Piercing | 16G (14G is also commonly used) | 1/4″ , 5/16″ and 3/8″ |
| Industrial Barbell | 14G (16G is also commonly used) | 1 1/2″ (varies) |
Beside above, which is thicker 14G or 16G?
Please refer to the metric conversion chart below.
| Gauge | Inches | Millimeters |
|---|---|---|
| 20G | .032″ | 0.81mm |
| 18G | .040″ | 1.0mm |
| 16G | .050″ | 1.2mm |
| 14G | .064″ | 1.6mm |
Moreover, how much does an industrial bar piercing cost?
Although the industrial piercing consists of two piercings, you’ll usually only be charged for one. It typically costs somewhere around $30 – $70. As always, choose a quality piercer over expense. Never go to a piercer who uses a piercing gun.
Does Claire’s do industrial bar piercings?
Gold Key Industrial Bar Cartilage Earring | Claire’s.
Do industrial piercing get infected easily?
Industrial piercings are more prone to infection because there are 2 wounds, and the tension placed on the skin from the jewelry also increases inflammation and vulnerability to the skin. An infection occurs when harmful bacteria build up in one or both of the holes where your ear is pierced.
Can you put a 14g in a 16g?
14g jewelry is larger than 16g jewelry, but you might be able to fit it. … The size difference between the two is small, but if you go back and forth it would obviously be a stretch every time you wanted to wear the 14’s, since your ear would shrink back to a 16g while you had that jewelry in.
How big is a 14 gauge piercing?
1.6 millimeters
Can I put a 14g in a 16g septum piercing?
Yes you can. The jewellery won’t be very snug, though, and might move around a lot. Having said that, the whole will probably close up a bit around the smaller gauge jewellery so you might not be able to wear 14g there any more. … So I used this 2mm diameter needle for a piercing with a 16g jewellery.
Do Industrial Bar holes close?
The industrial piercing goes through cartilage in your ear and depending on how long it has been pierced it will close eventually and faster than many other piercings because of the location.
Are there different size industrial bars?
Because every ear is different, the room between the two piercing holes differs from person to person. Therefore the standard measure of the industrial barbell has the longest length, 38 mm. That’s long enough for everyone. … For small ears, there are also many industrial barbells available with a length of 35 to 32 mm.
Can you sleep on an industrial piercing?
Sleeping with your piercing on the pillow means pressure over an extended period of time. This can cause irritation, pain, and swelling. If you tend to sleep on your side, your best bet is to pierce one ear at a time. … This allows you to put your ear in the hole, so you can rest on your side without irritation.
Is industrial piercing worth it?
I am able to sleep on my side that has the industrial now that it is fully healed. … Yeah the year of healing was a pain, but like everyone else here has stated, totally worth it. I’ve had mine for going on two years and it’s my favorite piercing of the three (four tomorrow) I have.
Should I move my industrial piercing while cleaning it?
–Never spin the jewelry, move it back and forth, or move it while you’re cleaning it. The jewelry may feel tight or like it’s not moving around and that is OK. It will move around on it’s own. –In your shower, avoid any shampoo, conditioner or soap on the piercing.
Are industrial piercings dangerous?
Industrial Piercing Risks
As long as you do double the work and don’t try to cut any corners though when it comes to aftercare, you can cut down on some of the risk. With two piercings being done on the cartilage instead of skin, you do have a slight risk of excessive bleeding.
