What size bar is used for industrial piercing?

Standard piercing sizes

Piercing Standard Gauge Standard Length
Industrial Barbell 14G (16G is also commonly used) 1 1/2″ (varies)
Labret Lip Rings 14G or 16G 1/4″ , 5/16″, and 3/8″
Monroe Piercing 16G 1/4″ , 5/16″ and 3/8″
Nipple Piercing 14G 3/8″ , 1/2″, 9/16″

>> Click to read more <<

Hereof, can I put a 14G in a 16G industrial?

The 14g is a larger barbell than the 16g by a fraction of an inch (0.013). Most piercers will have a preference between 14 and 16g for industrial piercings and while having a 14g means you can swap out for 16g jewelry you cannot do it the other way around without pain.

Subsequently, which is smaller 16G or 14G? Please refer to the metric conversion chart below.
Gauge Inches Millimeters
18G .040″ 1.0mm
16G .050″ 1.2mm
14G .064″ 1.6mm
12G .082″ 2.0mm

Besides, what size is my Industrial bar?

The length of the barbell can range from 28-55mm in length depending on how far apart the piercing holes are located on your ear and of course by how large your ear is. The angle of the piercings and distance between the piercings will determine if a barbell industrial piercing is a good selection for you personally.

Do industrial piercing get infected easily?

Industrial piercings are more prone to infection because there are 2 wounds, and the tension placed on the skin from the jewelry also increases inflammation and vulnerability to the skin. An infection occurs when harmful bacteria build up in one or both of the holes where your ear is pierced.

Should I move my industrial piercing while cleaning it?

–Never spin the jewelry, move it back and forth, or move it while you’re cleaning it. The jewelry may feel tight or like it’s not moving around and that is OK. It will move around on it’s own. –In your shower, avoid any shampoo, conditioner or soap on the piercing.

Is 14g or 16g bigger?

14g is bigger. The lower the number, the bigger the needle or jewelry. … So buy 16g jewelry and a 14g needle, or 14g jewelry and a 12g needle.

Can I put hoops in my industrial piercing?

Straight barbells aren’t necessarily the only piece of jewelry that can be put in your Industrial piercing; you can even put a hoop in each piercing hole, or even two studs, as long as the barbell is the right gauge.

What else can I put in my industrial piercing?

Alternatives to an Industrial Piercing bar

  1. Anti-helix-piercing.
  2. Anti-tragus-piercing.
  3. Conch-piercing.
  4. Daith-piercing.
  5. Rook-piercing.
  6. Scapha-piercing.
  7. Snug-piercing.
  8. Vertical-helix-piercing.

Is 18 or 22 gauge bigger?

Remember, smaller numbers are always thicker. For example, a 22 gauge (0.64mm) nose hoop is thinner than an 18 gauge (1.0mm) nose hoop. It’s incredibly important to make sure that you’re buying the correct gauge. Do not try to force a thicker piece of jewelry through your piercing.

Can I put a 20g in a 16g piercing?

Yes you can, in fact that’s typically what a piercer will do, especially with cartilage piercings. … Generally a piercer will use an 18f needle and use a 20g stud if it’s your ears for example. Take a look at this photo for example: The difference between 16g and 18g is about .

Is 14g or 16g better for septum?

There’s almost no difference between 14g and 16g and going between the 2 sizes once your healed shouldn’t honestly be too much of an issue. 16g jewelry is usually cheaper especially when you get into BVLA gold clickers and what not.

Can you sleep on an industrial piercing?

Can I sleep on my industrial piercing? You want to avoid sleeping on an industrial piercing because it adds additional pressure on the jewelry. It will be more likely to have scarring if you sleep on it.

Do Industrial Bar holes close?

The industrial piercing goes through cartilage in your ear and depending on how long it has been pierced it will close eventually and faster than many other piercings because of the location.

Are all industrial bars the same size?

The barbell piercing worn in the ear cartilage goes by a few different names : The barbell is called an industrial barbell, construction bar, or industrial project bar. Sizing of these bars varies depending on the person, because everybody’s ears are a different size.

Leave a Reply