JEWELRY TYPE
| Standard Hoop Inner Diameter | |
|---|---|
| Ear Cartilage (Helix, Tragus, Lobe, etc.) | 5/16″ (8mm) |
| Earhead, Thin Helix (Hole near the edge) | 1/4″ (6-6.5mm) |
| Conch | 3/8″-1/2″ (10mm–12mm) |
| Nose | 5/16″ (8mm) |
Beside above, how do I know what gauge my piercing is?
You can use the following methods to measure the gauge of your piercing jewellery:
- BCR: Measure the width of the bar.
- Labret: Measure the width of the bar.
- Barbell: Measure the width of the bar.
- Septum Ring: Measure the width of the ring at its thickest section.
Then, can I put a 16 gauge in a 18 gauge hole cartilage?
Yes you can, in fact that’s typically what a piercer will do, especially with cartilage piercings. They pierce with a gauge size bigger than the actual jewelry. It allows room for swelling and placing the jewelry.
Can I put a 14G in a 16G piercing?
14g jewelry is larger than 16g jewelry, but you might be able to fit it. … The size difference between the two is small, but if you go back and forth it would obviously be a stretch every time you wanted to wear the 14’s, since your ear would shrink back to a 16g while you had that jewelry in.
Can your tragus be too small to pierce?
It’s uncommon for a tragus to be too small, but it does happen. Trying to pierce this area can result in piercing behind the tragus if it is not large enough. This can affect your ability to chew.
What size gauge is a normal earring?
20G
How big is a 14 gauge piercing?
1.6 millimeters
What is bigger a 20 or 18 gauge?
Gauges get larger with decreasing number (i.e. a size 00G is massive compared to a 20 gauge). with an 18 gauge. If you want it smaller, ask for a 20 or even 22 gauge when getting pierced.
Is 14G bigger than 16G?
Jewelry is measured through a gauge system (see chart below). The higher the gauge number the smaller the wire is. A standard “earring” is usually 20 gauge. Jewelry gauges/sizes can vary between manufacturers.
| Gauge | Millimeter | Inch |
|---|---|---|
| 16g | 1.2mm | 3/64″ |
| 14g | 1.6mm | 1/16″ |
| 12g | 2mm | 5/64″ |
| 10g | 2.4mm | 3/32″ |
What is the smallest size gauge for ears?
What’s the smallest ear stretching size? Standard ear piercings are usually done at 20g or 18g for traditional earrings and that works out at roughly 1mm.
Is 16G thicker than 18g?
Though it seemingly goes against logic, earrings and other jewelry gauge sizes actually get bigger the lower the number of the gauge. An 18 gauge, one of the smallest gauges, is actually smaller than a 16 gauge earring, with the largest gauges being 0, 00, and 000 gauge jewelry.
How can I increase my gauge size?
The best thing to do is allow your piercing the necessary time to heal before you stretch it further with a larger taper. Typically, you should wait at least 1 to 2 weeks for your piercing to heal for the first few tapers. It may take 3 to 4 weeks for your piercing to heal for the larger tapers.
Can you stretch your ears every 2 weeks?
Depends on how well your body handles stretching. I just tried it every 2-3 weeks or so, pushed a taper through until i felt discomfort, then took it out. If it went all the way through, great, new jewellery in! If not, ease it out and try again a few weeks later.
